Saf-holland XL-LG321-01 Series CS615 Fruehauf Replaceable Land Manuel d'utilisateur télécharger pdf

DO NOT deviate from these instructions. Any changes or

deviations will void all warranties, expressed or implied,

unless written consent is first obtained from the factory.

OPERATION OF HOLLAND

FORMULA 150 LANDING GEAR:

NOTE: Holland Formula 150 2-speed gearbox has high

and low range gears. High range gear is to be used only

for rapid traverse up from and down to the ground and

is not intended to lift or lower any load. For additional

information, see Holland publication XL-FW302-XX,

entitled “Fifth Wheel Operating Instructions”.

TO EXTEND:

On outside mounted landing gear, engage the crank with

the crankshaft and turn the crank clockwise. Inside mounted

landing gear are extended by turning the crank counter-

clockwise. Using high gear, lower the landing gear until the

pads make contact with the ground. To reduce the load on

the fifth wheel, shift to low gear and crank an additional

four to eight turns. Leave the landing gear in low gear and

store the crank handle in the holder provided.

TO RETRACT:

On outside mounted landing gear, engage crank with

crankshaft and turn the crank counterclockwise. Inside

mounted landing gear are retracted by turning the crank

clockwise. Retract the landing gear using low gear until

unloaded. Then shift to high gear and continue cranking

until fully retracted. Leave the crankshaft engaged to

prevent road vibration wind-down. Store the crank in

the holder provided.

MAINTENANCE:

LUBRICATION:

Although Formula 150 landing gear are adequately

greased and packed with high quality lubricants when

manufactured, it may be necessary to periodically supple-

ment this lubrication to maintain satisfactory performance

for your particular application.

1. Lube both legs through the grease fittings and access

holes provided in the legs two times a year or as required.

2. Lube 2-speed gears through the grease fitting in the

gearbox two times a year or as required.

TROUBLE SHOOTING — HARD TURNING

LANDING GEAR — CHECK THE FOLLOWING:

1. Binding cross shaft. Bolts in the cross shaft must not

be overtightened to prevent lateral movement of the

cross shaft.

2. To determine which leg turns hard, remove the cross

shaft and operate each leg individually.

3. Landing gear may be bent or damaged.

4. Alignment – legs must be parallel and extend and

retract evenly.

5. Legs and gearbox may need additional lubrication.

6. If crankshaft holder or extension are used, check

for alignment with crankshaft.

7. If a through-axle is used, check for binding where

the axle goes through the legs.

8. Binding shaft bushings – bushings must have

adequate clearance for operation. Check mounting

for proper clearance.

9. Examine nut and screw assembly for damage caused

by dropping of the trailer.

TROUBLE SHOOTING — GENERAL:

Follow the dismantling and assembly instructions in

this manual.

If crankshaft jams or skips while turning–examine parts

(10 & 13) and all gearbox gears for worn, broken, or

missing teeth.

If the landing gear will not stay in gear while

cranking–check the condition of shifter spring (29),

shifter grooves in crankshaft (27) and cluster gear (28).

Replace as required.

XL-LG321-01 1

OPERATING, MAINTENANCE

and REPAIR PROCEDURES

Operating, Maintenance, and Repair Procedures

for Series CS615 Fruehauf

Replaceable Landing Gear

CAUTION

• Always grip crank handle securely.

• Always grip crank handle securely

with both hands before shifting.

• Never shift landing gear

under load.

• Never leave the crank unsecured.

• Never raise or lower a loaded

trailer in high gear.

WARNING

DO NOT use lubricants

containing teflon.

1 2 3 4

Résumé du contenu

Page 1 - OPERATING, MAINTENANCE

DO NOT deviate from these instructions. Any changes ordeviations will void all warranties, expressed or implied,unless written consent is first obtain

Page 2 - PROCEDURE:

SINGLE SPEED LEG DISMANTLING PROCEDURE:1. Remove landing gear from trailer.2. Remove rust from projecting end(s) of shaft (11), andlubricate for easy

Page 3

1 XA-06220-1-4-615 2 Inner leg & screw assy. 16" travel1A XA-06220-2-4-615 2 Inner leg & screw assy. 18.5" travel2 XA-06215-1L-402 1

Page 4 - XL-LG321-01

This product is covered by Holland’s Formula 150 5-year parts and 2-year labor warranty. Holland reserves the right,without giving prior notice, to ch

Commentaires sur ces manuels

Pas de commentaire

Saf-holland XL-LG321-01 Series CS615 Fruehauf Replaceable Land Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Saf-holland XL-LG321-01 Series CS615 Fruehauf Replaceable Land. SAF-HOLLAND XL-LG321-01 Series CS615 Fruehauf Replaceable Landing Gear User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Saf-holland XL-LG321-01 Series CS615 Fruehauf Replaceable Land