Saf-holland XL-FW421-02 XA-201-A-80-L Air Release Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Saf-holland XL-FW421-02 XA-201-A-80-L Air Release. SAF-HOLLAND XL-FW421-02 XA-201-A-80-L Air Release User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 8
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Coupling Procedures
1. Inspect the fifth wheel mounting.
Tighten loose
fasteners
Replace missing
fasteners
Repair/replace
cracked
components
NOTE: If you have a sliding fifth wheel, make sure
both plungers are fully engaged (locked).
(See Page 4, Figure 4B)
2. Make sure coupling area is flat, level and clear
of persons and obstacles.
3. Lubricate the fifth wheel-to-trailer contact
surface with grease. Tilt the ramps down.
XL-FW421-02
TILT
DOWNWARD
4. Make sure the locks are open. To open locks,
slide the handle forward and pull it out to the
maximum extension. The lock will swing to
the open position. Note: When you first receive
your fifth wheel, you may have to pry open the lock.
5. Center fifth wheel with kingpin.
6. Back tractor close to trailer and STOP.
LOCK OPEN
POSITION
ACTUATING FINGER
1
FLEETMASTER
XA-201-A-80-L AIR RELEASE
OPERATING INSTRUCTIONS &
MAINTENANCE PROCEDURES
OPERATING INSTRUCTIONS
This air release option fifth wheel
top plate is not intended to be
mounted onto low mount stationary brackets (Part
No. XA-7586 and XA-7886). Low mount brackets
do not provide sufficient clearance for the air
cylinder which can be damaged when the fifth
wheel is articulated.
You must read and understand the following instructions before operating your fifth
wheel. Failure to follow all of the important maintenance procedures contained in
these instructions may result in a hazardous condition or cause a hazardous condition to develop.
All maintenance must be performed by a qualified person using proper tools and safe procedures.
All maintenance must be performed while the tractor is uncoupled from the trailer.
Vue de la page 0
1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - FLEETMASTER

Coupling Procedures1. Inspect the fifth wheel mounting.• Tighten loosefasteners• Replace missingfasteners• Repair/replacecrackedcomponentsNOTE: If you

Page 2 - OPERATING INSTRUCTIONS

7. Chock trailer wheels.8. Connect brake lines and light cord.9. Support slack in lines to prevent interference.10. Set trailer brakes.11. Adjust trai

Page 3

8. Disconnect brake lines and light cord. Attachbrake line to dummy coupling to keep line clean.9. Actuate the fifth wheel control valve to openthe lo

Page 4

5. Slowly drive the tractor forward or backward toposition the fifth wheel.6. Re-engage the slide locking plungers. Verifythat both plungers have full

Page 5 - MAINTENANCE PROCEDURES

1. IMPORTANT! Alwaysmaintain adequatelubrication in fifthwheel lockingmechanism. Relubeas necessary (see Figure 1).2. Keep a lowtemperature, waterresi

Page 6

Inspection – Locking Mechanism1. Check the operation of the fifth wheel lockingmechanism using a Holland TF-TLN-5001 (2” kingpin) Lock Adjustment Tool

Page 7

Improper adjustment can causeimproper locking of the fifthwheel. If the fifth wheel does not operateproperly, DO NOT USE IT! Repeat the aboveadjustmen

Page 8

1. Loosen lock nut and turn the adjustment boltout (counter-clockwise).2. Disengage and engage the locking plungers.Verify that plungers have engaged

Commentaires sur ces manuels

Pas de commentaire